RDP Home Page Banner

Model 43 Compression Load Cell


High accuracy
High cycle life
Stainless steel
Infinite resolution
image of Model  43 Compression Load Cell
Our SLC43 load cell or force sensor is a device which converts load or force into an electrical signal.
The SLC43 load cell should be mounted on a hard, flat surface. Our SLC43 compression load cell measures the force applied to the load button.
Care should be taken to ensure that the model SLC43 load sensor is not exposed to load or force in excess of its capability. The range of model SLC43 compression load cell selected should therefore be appropriate for the maximum force (including transient forces) that can be applied to it.
The SLC43 transducer is a strain gauge type transducer and has a mV output which may require an amplifier. For the SLC43 we can offer a variety of high quality, low noise and high precision strain gauge amplifiers.
Compression Load Cell
Our SLC43 compression load cell measures the force applied to the load button.
dimensional drawing of  Model  43 Compression Load Cell
Connector sold separately
H2=4.6mm
Connector housing A B C
5lbs (22N) to 5000lbs (22kN) 21mm 19mm 32mm
7500lbs (33kN) to 500000lbs (2.2MN) 32mm 38mm 51mm
Type Range D1 H E PCD D2
SLC43/000005 5lbs (22N) 64mm 25mm #8 50.8mm 9mm
SLC43/000010 10lbs (44N) 64mm 25mm #8 50.8mm 9mm
SLC43/000025 25lbs (111N) 64mm 25mm #8 50.8mm 9mm
SLC43/000050 50lbs (222N) 76mm 30mm 6.4mm 57.2mm 14mm
SLC43/000100 100lbs (445N) 76mm 30mm 6.4mm 57.2mm 14mm
SLC43/000250 250lbs (1.1kN) 76mm 30mm 6.4mm 57.2mm 14mm
SLC43/000500 500lbs (2.2kN) 76mm 30mm 6.4mm 57.2mm 14mm
SLC43/001000 1000lbs (4.4kN) 76mm 30mm 6.4mm 57.2mm 14mm
SLC43/002000 2000lbs (8.9kN) 89mm 30mm 7.9mm 66.7mm 18mm
SLC43/003000 3000lbs (13kN) 89mm 30mm 7.9mm 66.7mm 18mm
SLC43/004000 4000lbs (18kN) 89mm 30mm 7.9mm 66.7mm 18mm
SLC43/005000 5000lbs (22kN) 89mm 30mm 7.9mm 66.7mm 18mm
SLC43/007500 7500lbs (33kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/010000 10000lbs (44kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/015000 15000lbs (67kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/020000 20000lbs (89kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/030000 30000lbs (133kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/050000 50000lbs (222kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/075000 75000lbs (334kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/100000 100000lbs (445kN) 114mm 51mm 9.5mm 96.3mm 38mm
SLC43/150000 150000lbs (667kN) 140mm 55mm 9.5mm 122.2mm 51mm
SLC43/200000 200000lbs (890kN) 140mm 55mm 9.5mm 122.2mm 51mm
SLC43/300000 300000lbs (1.3MN) 178mm 68mm 9.5mm 152.4mm 64mm
SLC43/400000 400000lbs (1.8MN) 191mm 68mm 9.5mm 171.5mm 64mm
SLC43/500000 500000lbs (2.2MN) 279mm 114mm 19.1mm 241.3mm 121mm
Specification
Excitation/supply (acceptable) 0 to 15V (ac or dc)
Excitation/supply (calibrated) 10Vdc
Output ≤25lbs≈2mV/V. ≥50lbs≈3mV/V
Bridge resistance 350 Ω
Linearity error ≤25lbs = ±0.2% F.S.
≥50lbs = ±0.1% F.S.
Hysteresis ≤25lbs = ±0.1% F.S.
≥50lbs = ±0.08% F.S.
Repeatability ≤25lbs = ±0.1% F.S.
≥50lbs = ±0.03% F.S.
Temperature coefficient (zero) ±0.004% F.S. /℃
Temperature coefficient (span) ±0.004% rdg /℃
Operating temperature range -54℃ to 121℃
Compensated temperature range 16℃ to 71℃
Deflection at full scale 0.08mm maximum
Over-range capacity 50% F.S.
Major construction material 17-4 PH stainless steel
Mating connector <=5000 lbs = SEN1005 (PT0A-10-6S (or equivalent))
>=7500 lbs = SEN1006 (MS3106A-14S-6S (or equivalent))

Options and accessories