Model RLT Tension Load Cell

Very high accuracy
Infinite resolution
Low cost



A load cell or force sensor is a device which converts load or force into an electrical signal.

A tension load cell measures the tension force applied between the top and bottom mounting threads.

Care should be taken to ensure that the load sensor is not exposed to load or force in excess of its capability. The range of tension load cell selected should therefore be appropriate for the maximum force (including transient forces) that can be applied to it.

This series of transducer is a strain gauge type transducer and has a mV output which may require an amplifier. We can offer a variety of high quality, low noise and high precision strain gauge amplifiers.


How it Works - Strain Gauge Load Cell

   RL technical manual (103kb)

   Data sheet (181kb)

CD1 = 0.5''
CD2 = 0.20'' 0.01''
CL1 = 0.9''
CL2 = 1.1''
Type Range A B C D Mounting thread
RLT0005 5kgf (11lbs) 2.5'' 2.0'' 0.5'' 0.8'' M8 X 1.25
RLT0010 10kgf (22lbs) 2.5'' 2.0'' 0.5'' 0.8'' M8 X 1.25
RLT0020 20kgf (44lbs) 2.5'' 2.0'' 0.5'' 0.8'' M8 X 1.25
RLT0050 50kgf (110lbs) 2.5'' 2.0'' 0.5'' 0.8'' M8 X 1.25
RLT0075 75kgf (165lbs) 2.5'' 2.0'' 0.5'' 0.8'' M8 X 1.25
RLT0100 100kgf (221lbs) 3.0'' 2.0'' 0.8'' 1.0'' M10 X 1.5
RLT0250 250kgf (551lbs) 3.0'' 2.0'' 0.8'' 1.0'' M12 X 1.75
RLT0500 500kgf (1.1klbs) 3.0'' 2.0'' 0.8'' 1.0'' M12 X 1.75
RLT0750 750kgf (1.7klbs) 3.0'' 2.0'' 0.8'' 1.0'' M12 X 1.75
RLT1000 1000kgf (2.2klbs) 3.0'' 2.0'' 1.0'' 1.3'' M12 X 1.75
RLT1500 1500kgf (3.3klbs) 3.0'' 2.0'' 1.0'' 1.3'' M12 X 1.75
RLT2000 2000kgf (4.4klbs) 4.3'' 3.0'' 1.0'' 1.3'' M18 X 1.5
RLT2500 2500kgf (5.5klbs) 4.3'' 3.0'' 1.0'' 1.3'' M18 X 1.5

Specification

Excitation/supply (acceptable)0 to 15V Temperature coefficient (zero) 0.002% F.S. /F (typical)
Excitation/supply (calibrated)10V Temperature coefficient (span) 0.002% F.S. /F (typical)
Output2mV/V 10% Operating temperature range -4F to 140F
Zero balance2% F.S. Compensated temperature range 14F to 104F
Bridge resistance350 Ohms Ingress protection (IP) 65
Linearity error0.03% F.S. Over-range capacity 50%
Hysteresis0.03% F.S. Major construction material Steel
Repeatability0.03% F.S. Electrical termination 9.8ft (integral cable)
ResolutionInfinite    


Options and accessories

Electronics


All dimensions and specifications are nominal. www.rdpe.com/us/rlt.htm 20141105
Due to our policy of on-going development, specifications may change without notice. Any modification may affect some or all of the specifications for our equipment.
 

RDP Electrosense
2216 Pottstown Pike
Pottstown, PA 19465
USA
Tel: 610-469-0850
Tel: 800-334-5838
Fax: 610-469-0852
Email: info@rdpe.com

-