RDP Home Page Banner
Model RLT Tension Load Cell

Very high accuracy
Infinite resolution
Low cost
dimensional drawing of  Model  RLT Tension Load Cell
A load cell or force sensor is a device which converts load or force into an electrical signal.
Care should be taken to ensure that the load sensor is not exposed to load or force in excess of its capability. The range of tension load cell selected should therefore be appropriate for the maximum force (including transient forces) that can be applied to it.
This series of transducer is a strain gauge type transducer and has a mV output which may require an amplifier. We can offer a variety of high quality, low noise and high precision strain gauge amplifiers.
Tension Load Cell
A tension load cell measures the tension force applied between the top and bottom mounting threads.
dimensional drawing of  Model  RLT Tension Load Cell
CD1=13.6mm
CD2=5.05mm ±0.15mm
CL1=22mm
CL2=27mm
Type Range A B C D Mounting thread
RLT0005 5kgf (49N) 63.5mm 50.8mm 12.7mm 19.1mm M8 X 1.25
RLT0010 10kgf (98N) 63.5mm 50.8mm 12.7mm 19.1mm M8 X 1.25
RLT0020 20kgf (196N) 63.5mm 50.8mm 12.7mm 19.1mm M8 X 1.25
RLT0050 50kgf (491N) 63.5mm 50.8mm 12.7mm 19.1mm M8 X 1.25
RLT0075 75kgf (736N) 63.5mm 50.8mm 12.7mm 19.1mm M8 X 1.25
RLT0100 100kgf (981N) 76.2mm 50.8mm 19.1mm 25.4mm M10 X 1.5
RLT0250 250kgf (2kN) 76.2mm 50.8mm 19.1mm 25.4mm M12 X 1.75
RLT0500 500kgf (5kN) 76.2mm 50.8mm 19.1mm 25.4mm M12 X 1.75
RLT0750 750kgf (7kN) 76.2mm 50.8mm 19.1mm 25.4mm M12 X 1.75
RLT1000 1000kgf (10kN) 76.2mm 50.8mm 25.4mm 31.8mm M12 X 1.75
RLT1500 1500kgf (15kN) 76.2mm 50.8mm 25.4mm 31.8mm M12 X 1.75
RLT2000 2000kgf (20kN) 108.0mm 76.2mm 25.4mm 31.8mm M18 X 1.5
RLT2500 2500kgf (25kN) 108.0mm 76.2mm 25.4mm 31.8mm M18 X 1.5
Specification
Excitation/supply (acceptable) 0 to 15V
Excitation/supply (calibrated) 10V
Output 2mV/V ±10%
Zero balance 2% F.S.
Bridge resistance 350 Ω
Linearity error ±0.03% F.S.
Hysteresis ±0.03% F.S.
Repeatability ±0.03% F.S.
Resolution Infinite
Temperature coefficient (zero) ±0.003% F.S. /℃ (typical)
Temperature coefficient (span) ±0.003% F.S. /℃ (typical)
Operating temperature range -20℃ to 60℃
Compensated temperature range -10℃ to 40℃
Ingress protection (IP) 65
Over-range capacity 50%
Major construction material Steel
Electrical termination 3m (integral cable)

Options and accessories

Due to our policy of on-going development, specifications may change without notice. Any modification may affect some or all of the specifications for our equipment. All dimensions and specifications are nominal.
www.rdpe.com/ex/rlt.html
20190308