RDP Home Page Banner

Model MPB Compression Load Cell

High Range
High cycle life
Stainless steel
Infinite resolution
image of Model  MPB Compression Load Cell
Our SLC-MPB load cell or force sensor is a device which converts load or force into an electrical signal.
The SLC-MPB load cell should be mounted on a hard, flat surface. This compression load cell measures the compressive force applied between the top and bottom of the load cell.
Care should be taken to ensure that the model SLC-MPB load sensor is not exposed to load or force in excess of its capability. The range of model SLC-MPB compression load cell selected should therefore be appropriate for the maximum force (including transient forces) that can be applied to it.
The SLC-MPB transducer is a strain gauge type transducer and has a mV output which may require an amplifier. For the SLC-MPB we can offer a variety of high quality, low noise and high precision strain gauge amplifiers.
Compression Load Cell
Our SLC-MPB compression load cell measures the force applied to the load button.
dimensional drawing of  Model  MPB Compression Load Cell
Connector sold separately
Type Range H H2 H3 OD D1 D2 T D
SLC-MPB-T0001 1tons (10kN) 19.1mm 0.5mm 1.5mm 22.1mm 6.6mm 9.4mm 8-32 UNC 4.6mm
SLC-MPB-T0002.5 2.5tons (25kN) 19.1mm 0.5mm 1.5mm 22.1mm 6.6mm 9.4mm 8-32 UNC 4.6mm
SLC-MPB-T0005 5tons (50kN) 22.4mm 1.0mm 1.5mm 24.9mm 10.4mm 13.5mm 8-32 UNC 4.6mm
SLC-MPB-T0010 10tons (100kN) 28.4mm 1.5mm 4.1mm 37.8mm 19.1mm 19.1mm 1/4-28 UNF 6.4mm
SLC-MPB-T0025 25tons (249kN) 45.0mm 3.0mm 7.6mm 49.8mm 30.0mm 30.0mm 1/4-28 UNF 6.4mm
SLC-MPB-T0050 50tons (498kN) 64.0mm 4.6mm 4.8mm 62.0mm 40.4mm 40.4mm 3/8-24 UNF 9.7mm
SLC-MPB-T0100 100tons (996kN) 85.9mm 6.4mm 17.5mm 81.0mm 57.2mm 57.2mm 3/8-24 UNF 9.7mm
SLC-MPB-T0250 250tons (2.5MN) 135.9mm 6.4mm 43.2mm 112.8mm 90.7mm 90.7mm 3/4-16 UNF 19.1mm
SLC-MPB-T0500 500tons (5MN) 192.3mm 6.4mm 66.0mm 163.6mm 128.3mm 128.3mm 3/4-16 UNF 19.1mm
SLC-MPB-T1000 1000tons (10MN) 264.4mm 6.4mm 101.6mm 214.4mm 181.4mm 181.4mm 1-12 UNF 25.4mm
Excitation/supply (calibrated) 10Vdc
Bridge resistance 350 Ω
Repeatability ±0.02% F.S.
Resolution Infinite
Temperature coefficient (zero) ±0.018% F.S. /℃
Temperature coefficient (span) ±0.02% rdg /℃
Operating temperature range -57℃ to 121℃
Compensated temperature range 21℃ to 71℃
Fatigue life (nominal) 1000000
Over-range capacity 50% F.S.
Major construction material 17-4 PH stainless steel
Mating connector SEN1005 (PT0A-10-6S (or equivalent))

Options and accessories