RDP Home Page Banner

Model MPB Compression Load Cell

High Range
High cycle life
Stainless steel
Infinite resolution
image of Model MPB Compression Load Cell
Our SLC-MPB load cell or force sensor is a device which converts load or force into an electrical signal.
The SLC-MPB load cell should be mounted on a hard, flat surface. This compression load cell measures the compressive force applied between the top and bottom of the load cell.
Care should be taken to ensure that the model SLC-MPB load sensor is not exposed to load or force in excess of its capability. The range of model SLC-MPB compression load cell selected should therefore be appropriate for the maximum force (including transient forces) that can be applied to it.
The SLC-MPB transducer is a strain gauge type transducer and has a mV output which may require an amplifier. For the SLC-MPB we can offer a variety of high quality, low noise and high precision strain gauge amplifiers.
Compression Load Cell
Our SLC-MPB compression load cell measures the force applied to the load button.
dimensional drawing of Model MPB Compression Load Cell
Connector sold separately
Type Range H H2 H3 OD D1 D2 T D
SLC-MPB-T0001 1tons (2.2klbs) 0.75'' 0.02'' 0.06'' 0.87'' 0.26'' 0.37'' 8-32 UNC 0.18''
SLC-MPB-T0002.5 2.5tons (5.6klbs) 0.75'' 0.02'' 0.06'' 0.87'' 0.26'' 0.37'' 8-32 UNC 0.18''
SLC-MPB-T0005 5tons (11klbs) 0.88'' 0.04'' 0.06'' 0.98'' 0.41'' 0.53'' 8-32 UNC 0.18''
SLC-MPB-T0010 10tons (22klbs) 1.12'' 0.06'' 0.2'' 1.49'' 0.75'' 0.75'' 1/4-28 UNF 0.25''
SLC-MPB-T0025 25tons (56klbs) 1.77'' 0.12'' 0.3'' 1.96'' 1.18'' 1.18'' 1/4-28 UNF 0.25''
SLC-MPB-T0050 50tons (112klbs) 2.52'' 0.18'' 0.2'' 2.44'' 1.59'' 1.59'' 3/8-24 UNF 0.38''
SLC-MPB-T0100 100tons (224klbs) 3.38'' 0.25'' 0.7'' 3.19'' 2.25'' 2.25'' 3/8-24 UNF 0.38''
SLC-MPB-T0250 250tons (560klbs) 5.35'' 0.25'' 1.7'' 4.44'' 3.57'' 3.57'' 3/4-16 UNF 0.75''
SLC-MPB-T0500 500tons (1120klbs) 7.57'' 0.25'' 2.6'' 6.44'' 5.05'' 5.05'' 3/4-16 UNF 0.75''
SLC-MPB-T1000 1000tons (2240klbs) 10.41'' 0.25'' 4.0'' 8.44'' 7.14'' 7.14'' 1-12 UNF 1.00''
Specification
Excitation/supply (calibrated) 10Vdc
Bridge resistance 350 Ω
Repeatability ±0.02% F.S.
Resolution Infinite
Temperature coefficient (zero) ±0.010% F.S. /℉
Temperature coefficient (span) ±0.010% rdg /℉
Operating temperature range -71℉ to 250℉
Compensated temperature range 70℉ to 160℉
Fatigue life (nominal) 1000000
Over-range capacity 50% F.S.
Major construction material 17-4 PH stainless steel
Mating connector SEN1005 (PT0A-10-6S (or equivalent))
Options and accessories
Amplifiers Amplifier option thumbnail
Panel meter Panel meter option thumbnail